Use simulation to test the impact of changing the resource, route or centre
Introduction
The programme “Use simulation to test the impact of changing the resource, route or centre” addresses a practical task within Supply Chain Planning and Integration. Training draws on demand, capacity, inventory and supplier and transport lead times and uses techniques for analysing flow and dependencies and balancing cost and service to link the analysis to a traceable decision and action.
The participant develops a requirements and supplier comparison file over 5 training days, then tests it in a practical case on “Use simulation to test the impact of changing the resource, route or centre” involving a supplier disruption, change in demand or transport delay. The output is reviewed against service level, flow time and disruption risks and the next step for applying it in the workplace is identified.
Objectives
By the end of the programme, participants work towards the following:
- Define the scope of Use simulation to test the impact of changing the resource, route or centre and the requirements for completing the task.
- Prepare and check the practical exercise inputs using demand, capacity, inventory and supplier and transport lead times.
- Apply the following method: analysing flow and dependencies and balancing cost and service to produce a requirements and supplier comparison file.
- Test the outcome in the event of a supplier disruption, change in demand or transport delay and document the correction.
- Present and assess the output using service level, flow time and disruption risks and define an implementation plan.
Programme topics
Day 1: Defining the scope of the exercise and completion requirements
- Translate the programme title “Use simulation to test the impact of changing the resource, route or centre” into a task, a defined scope and a reviewable output
- Translate the requirement into a specification and acceptance criterion
- Identify the data and stakeholders required from demand, capacity, inventory and supplier and transport lead times
Day 2: Preparing data and evidence and establishing a baseline
- Prepare case data for “Use simulation to test the impact of changing the resource, route or centre” and check its completeness and consistency
- Document assumptions and the source of each input in a requirements and supplier comparison file
- Identify the gap between the current situation and the target outcome using service level, flow time and disruption risks
Day 3: Developing the solution and carrying out the specialist task
- Compare price, total cost and risks
- Produce the first version of a requirements and supplier comparison file to support “Use simulation to test the impact of changing the resource, route or centre”
- Link each result to its source using analysing flow and dependencies and balancing cost and service
Day 4: Testing alternatives and exceptions and reviewing the output
- Complete a practical case on “Use simulation to test the impact of changing the resource, route or centre” involving a supplier disruption, change in demand or transport delay
- Define the supplier’s commitments and review performance and escalation
- Record discrepancies, errors, validity limits and corrective decisions in a requirements and supplier comparison file
Day 5: Presenting the practical output and workplace transfer plan
- Present a requirements and supplier comparison file resulting from “Use simulation to test the impact of changing the resource, route or centre” and review it with the training group
- Measure completion of the practical exercise using service level, flow time and disruption risks and trace the evidence
- Develop an implementation plan specifying the responsible person, deadline, approval decision and outcome monitoring mechanism
Outputs
- a requirements and supplier comparison file tailored to the subject of “Use simulation to test the impact of changing the resource, route or centre”, with traceability of data, assumptions and decisions.
- Results of testing a practical case on “Use simulation to test the impact of changing the resource, route or centre” involving a supplier disruption, change in demand or transport delay, with documented findings and how they were addressed.
- An implementation plan that measures service level, flow time and disruption risks and identifies the responsible person, deadline and review mechanism.
Who should attend
- Supply chain, procurement, operations and logistics planners
- Team members assigned to implement or review “Use simulation to test the impact of changing the resource, route or centre” whose responsibilities relate to Supply Chain Planning and Integration.
Participation requirements and delivery methodology
- Experience or a work assignment related to Supply Chain Planning and Integration that enables participation in practical exercises and discussion of alternatives.
- Training and hypothetical data are used. Personal data and confidential documents are excluded from classroom exercises.
- Practical workshops, evidence reviews and case simulations addressing Use simulation to test the impact of changing the resource, route or centre, with the output developed progressively throughout the programme.
- The output is assessed for completeness, consistency of sources and its ability to measure service level, flow time and disruption risks.
Conclusion
The programme “Use simulation to test the impact of changing the resource, route or centre” concludes with a presentation of a requirements and supplier comparison file and an explanation of the underlying evidence, decisions and alternatives. Application limits and outstanding findings are recorded and converted into a follow-up plan with a responsible person, a deadline and a clear measure.
