Lean applied to financial transaction steps to reduce re-employment and waiting time
Introduction
The programme “Lean applied to financial transaction steps to reduce re-employment and waiting time” addresses a practical task within Treasury, Liquidity, Cost and Asset Management. Training draws on amounts due, collections, payments and asset movements and uses techniques for reconciling movements and tracing cash and cost drivers to link the analysis to a traceable decision and action.
The participant develops a flow map and waste identification checklist over 5 training days, then tests it in a practical case on “Lean applied to financial transaction steps to reduce re-employment and waiting time” involving delayed collections, increased payments or a change in a cost driver. The output is reviewed against the cash gap, forecast accuracy and unit cost and the next step for applying it in the workplace is identified.
Objectives
By the end of the programme, participants work towards the following:
- Define the scope of Lean applied to financial transaction steps to reduce re-employment and waiting time and the requirements for completing the task.
- Prepare and check the practical exercise inputs using amounts due, collections, payments and asset movements.
- Apply the following method: reconciling movements and tracing cash and cost drivers to produce a flow map and waste identification checklist.
- Test the outcome in the event of delayed collections, increased payments or a change in a cost driver and document the correction.
- Present and assess the output using the cash gap, forecast accuracy and unit cost and define an implementation plan.
Programme topics
Day 1: Defining the scope of the exercise and completion requirements
- Translate the programme title “Lean applied to financial transaction steps to reduce re-employment and waiting time” into a task, a defined scope and a reviewable output
- Measure work, waiting and handovers
- Identify the data and stakeholders required from amounts due, collections, payments and asset movements
Day 2: Preparing data and evidence and establishing a baseline
- Prepare case data for “Lean applied to financial transaction steps to reduce re-employment and waiting time” and check its completeness and consistency
- Document assumptions and the source of each input in a flow map and waste identification checklist
- Identify the gap between the current situation and the target outcome using the cash gap, forecast accuracy and unit cost
Day 3: Developing the solution and carrying out the specialist task
- Distinguish necessary controls from rework
- Produce the first version of a flow map and waste identification checklist to support “Lean applied to financial transaction steps to reduce re-employment and waiting time”
- Link each result to its source using reconciling movements and tracing cash and cost drivers
Day 4: Testing alternatives and exceptions and reviewing the output
- Complete a practical case on “Lean applied to financial transaction steps to reduce re-employment and waiting time” involving delayed collections, increased payments or a change in a cost driver
- Run a limited simplification trial and measure its impact
- Record discrepancies, errors, validity limits and corrective decisions in a flow map and waste identification checklist
Day 5: Presenting the practical output and workplace transfer plan
- Present a flow map and waste identification checklist resulting from “Lean applied to financial transaction steps to reduce re-employment and waiting time” and review it with the training group
- Measure completion of the practical exercise using the cash gap, forecast accuracy and unit cost and trace the evidence
- Develop an implementation plan specifying the responsible person, deadline, approval decision and outcome monitoring mechanism
Outputs
- a flow map and waste identification checklist tailored to the subject of “Lean applied to financial transaction steps to reduce re-employment and waiting time”, with traceability of data, assumptions and decisions.
- Results of testing a practical case on “Lean applied to financial transaction steps to reduce re-employment and waiting time” involving delayed collections, increased payments or a change in a cost driver, with documented findings and how they were addressed.
- An implementation plan that measures the cash gap, forecast accuracy and unit cost and identifies the responsible person, deadline and review mechanism.
Who should attend
- Treasury, liquidity, cost and asset officers
- Team members assigned to implement or review “Lean applied to financial transaction steps to reduce re-employment and waiting time” whose responsibilities relate to Treasury, Liquidity, Cost and Asset Management.
Participation requirements and delivery methodology
- Experience or a work assignment related to Treasury, Liquidity, Cost and Asset Management that enables participation in practical exercises and discussion of alternatives.
- Training and hypothetical data are used. Personal data and confidential documents are excluded from classroom exercises.
- Practical workshops, evidence reviews and case simulations addressing Lean applied to financial transaction steps to reduce re-employment and waiting time, with the output developed progressively throughout the programme.
- The output is assessed for completeness, consistency of sources and its ability to measure the cash gap, forecast accuracy and unit cost.
- Applicable standards and regulations depend on the organization’s activities and jurisdiction. Authorized specialists review the outputs before they are used in an actual decision.
Conclusion
The programme “Lean applied to financial transaction steps to reduce re-employment and waiting time” concludes with a presentation of a flow map and waste identification checklist and an explanation of the underlying evidence, decisions and alternatives. Application limits and outstanding findings are recorded and converted into a follow-up plan with a responsible person, a deadline and a clear measure.
